料破碎机顾名思义是破碎塑料材质的破碎机。在注塑机或者造粒机生产原料的同时，产生的不良品和水口料，可以及时投入机边塑料破碎机，经过粉碎OK后，且保持粉碎之干净、干燥，在“雨料比例阀”定比例的情况下，原料与水口粉碎混合、成型，制造良品，循环利用。塑料破碎机与其他辅机（干燥机、除湿机、冷水机、模温机等）配合形成的“粉碎比例混合回收系统”的好处是水品料未及污染，而造成塑胶之物性——强度、密度、颜色光泽免遭破坏，故可提高产品之品质；其好处包括成本和材料的节省，流程管理的自动化改进，准无人车间的动作，竞争力的增强以及环境友善的制造活动。 A crusher is a crusher that is a broken plastic. In injection molding machine or the polymer in the production of raw materials at the same time, the defective product and shuikou expected, the machine can be timely input side plastic crusher, after crushing OK, and keep the crush of clean, dry, in the "rain material proportion valve" under the condition of constant proportion, raw material crushing and shuikou, molding, manufacturing fine products, recycling. Plastic crusher and other auxiliaries (drying machine, dehumidifier, cold water machine, die temperature machine, etc.) with formation of the "the benefits of the crushing ratio mixed recycling system" is not pollution, water quality caused by the plastic physical properties, strength, density, color, luster from damage, it can improve the quality of products; Its benefits include cost and material saving, automation of process management improvement, the action of unmanned workshop, enhanced competitiveness and environmental friendly manufacturing activities. 塑料破碎机的维护与保养 Maintenance and maintenance of plastic crusher 1、应把塑料破碎机安置通风位置,保证电机工作热量散发,延长其寿命. The plastic crusher should be put in the ventilation position to ensure the heat release of the motor and extend its life. 2、应定期对轴承加注润滑油,保证轴承间的润滑性. It is necessary to lubricate the bearings regularly to ensure the lubrication of the bearings. 3、定期检查刀具螺丝,全新塑料破碎机使用1小时后,用工具紧固动刀,定刀的螺丝,加强刀片与刀架间的固定性. Check the tool screw regularly, and the new plastic crusher will be used for one hour after using the tool to tighten the blade, set the screw of the knife, and strengthen the solidification between the blade and the frame. 4、为保证刀具切口的锋利度,应常检查刀具,保证其锋利度,减少由于刀锋钝缺而引起其它部件的不必要损坏. In order to guarantee the sharpness of the cutting edge, we should always check the cutting tools to ensure the cutting edge and reduce the unnecessary damage caused by the blunt lack of the blade. 5、更换刀具时,动刀与定刀之间的间隙:20HP以上破碎机0.8MM为佳,20HP以下的破碎机0.5MM为佳.回收料越薄,间隙可适当调大. 5, replacing knives, the knife and knife gap between: 0.8 MM is better, more than 20 HP crusher crusher 0.5 MM below 20 HP is preferred. The thinner recycled material, clearance can be appropriately adjusted. 6、第二次启动前,应先清除机室所剩余的碎料,减少启动阻力.应定期打开惯性罩和皮带轮罩,清除法兰盘下方出灰口,因塑料破碎机室排出粉料进入转轴轴承. 6, the second start, should first clear the rest of the machine room are broken material, reduce the starting resistance. Regularly open the inertial cover and belt guard, remove flange bottom ash, because of plastic crusher chamber discharge powder into the shaft bearing. 7、机器应保持良好接地. The machine should be kept well grounded. 8、定期检查塑料破碎机皮带是否松驰,及时调紧. Check the plastic crusher on a regular basis and tighten it in time.