联系我们
公司名称：XXX
电话：XXX
手机：XXX
联系人：XXX
地址：XXX
新闻动态
操作塑料机械注意事项
1、由于废旧塑料属于易燃品，在工作地点要做好防火设施，生产场所必须配备灭火器、消防栓。
Because used plastics are flammable, fire extinguishers and fire hydrants must be provided in the workplace.
2、出现故障或非正常声音时必须报告有管理员，并由专业维修人员来进行处理。如发现有影响安全的不正常现象出现，立即停机检查处理。
When a failure or abnormal sound is reported, an administrator must be reported and handled by professional maintenance personnel. If there is any abnormal occurrence that affects safety, immediately stop check and processing.
3、在操作的过程中，一定要防止带有沙石或者金属的原料进入挤塑机，以防螺杆、机筒的加剧磨损或卡死、损坏现象。
3, in the process of operation, must prevent with sand or metal material into the crowded molding machine, to prevent the aggravate wear of the screw and barrel or death, damage phenomenon.
4、塑料机械用油要使用清洁度、粘度等指标均符合要求的液压油，并按规定为油冷却器提供足够流量的冷却水，以免液压元件和管路因油液污染或高温产生阻塞、漏油等损坏现象。减速器必须加注符合要求的润滑油。
4, plastic machinery to use oil cleanliness, indexes meet the requirements, such as hydraulic oil viscosity, and in accordance with the provisions, to provide sufficient flow of cooling water for oil cooler, lest hydraulic components and pipe line for oil pollution damage phenomenon such as congestion, oil or high temperature. The gearbox must be filled with the required lubricating oil.
5、塑料机械在操作过程中一定要熟悉注意事项，严格按照操作规程要求，坚决杜绝违章操作。要确保安全装置的可靠性，不得为求方便而去掉设备的防护措施。
The plastic machinery must be familiar with the matter in the course of operation, strictly according to the rules of operation, and resolutely put an end to illegal operation. To ensure the reliability of the safety device, it is not necessary to remove the protective measures for the convenience of the equipment.
6、在机器开机之前要预热，预热不能达到设定的温度不要转动螺杆，保温时间不够时，决不能开机运转。
6, before the machine is turned on, pre-heat up the temperature not to reach the set temperature and not turn the screw. When the temperature is low, it must not be turned on.
7、新的操作员一定要进行培训，操作者必须要熟悉塑料机械结构性能及操作程序的操作者进行操作。
7, the new operator must be trained and the operator must be familiar with the performance of the plastic mechanical structure and the operator of the operation procedure.
Because used plastics are flammable, fire extinguishers and fire hydrants must be provided in the workplace.
2、出现故障或非正常声音时必须报告有管理员，并由专业维修人员来进行处理。如发现有影响安全的不正常现象出现，立即停机检查处理。
When a failure or abnormal sound is reported, an administrator must be reported and handled by professional maintenance personnel. If there is any abnormal occurrence that affects safety, immediately stop check and processing.
3、在操作的过程中，一定要防止带有沙石或者金属的原料进入挤塑机，以防螺杆、机筒的加剧磨损或卡死、损坏现象。
3, in the process of operation, must prevent with sand or metal material into the crowded molding machine, to prevent the aggravate wear of the screw and barrel or death, damage phenomenon.
4、塑料机械用油要使用清洁度、粘度等指标均符合要求的液压油，并按规定为油冷却器提供足够流量的冷却水，以免液压元件和管路因油液污染或高温产生阻塞、漏油等损坏现象。减速器必须加注符合要求的润滑油。
4, plastic machinery to use oil cleanliness, indexes meet the requirements, such as hydraulic oil viscosity, and in accordance with the provisions, to provide sufficient flow of cooling water for oil cooler, lest hydraulic components and pipe line for oil pollution damage phenomenon such as congestion, oil or high temperature. The gearbox must be filled with the required lubricating oil.
5、塑料机械在操作过程中一定要熟悉注意事项，严格按照操作规程要求，坚决杜绝违章操作。要确保安全装置的可靠性，不得为求方便而去掉设备的防护措施。
The plastic machinery must be familiar with the matter in the course of operation, strictly according to the rules of operation, and resolutely put an end to illegal operation. To ensure the reliability of the safety device, it is not necessary to remove the protective measures for the convenience of the equipment.
6、在机器开机之前要预热，预热不能达到设定的温度不要转动螺杆，保温时间不够时，决不能开机运转。
6, before the machine is turned on, pre-heat up the temperature not to reach the set temperature and not turn the screw. When the temperature is low, it must not be turned on.
7、新的操作员一定要进行培训，操作者必须要熟悉塑料机械结构性能及操作程序的操作者进行操作。
7, the new operator must be trained and the operator must be familiar with the performance of the plastic mechanical structure and the operator of the operation procedure.
